Optimise Your Monitoring

It’s all very well having a decent pair of monitors, but to get the most out of them there are several areas that need attention. A lot of them are completely free, just requiring your time and a bit of careful thought to optimise the setup. To get started, placement is critical – not too near the rear wall, and with listening position at the apex of a triangle that is equidistant from the side walls. The DSP Project‘s video, embedded above, provides an excellent starting point for understanding the process.

Monitor placement is critical – not too near the rear wall, and with listening position at the apex of a triangle

If your speakers are on a desk, then ideally the desk should be as solid and immovable as you can make it. If it isn’t then DIY bracing can help, and you may want to invest in some form of isolation. Auralex’s MoPADs are an excellent affordable option. Alternatively, speaker stands can be helpful – though these also need to be solid and well placed.

Once your monitors are set up as well as possible, you may also want to consider investing in a monitor control box. If you use the master fader in your DAW as the overall volume control when driving active speakers, then you may be limiting the dynamic range of your audio interface’s digital to analogue conversion stage. In fact, with your DAW’s master gain pulled down you may find that you’re mixing with 12-bit sound or less. A simple passive volume control allows you to adjust levels as you go without limiting dynamic range, setting a suitable listening throughout your session whether you’re soloing individual parts or listening to a final mix.

24th April, 2014

Comments

  • Thanks a lot for this very usefull article.

    Report
  • Great article : one doesn’t need lots of stuff to achieve great ideas.

    Always focus on the ideas, not on the gear.

    I would also add that a few cheap tricks can strongly improve your listening accoustics. Read SoundOnSound articles in their archives on that matter (Studio SOS). I lost so many many years working in poor acoustics. Now that I solved this problem is like if I had a new pair of expensive speakers.

    Report
  • On a 24bit system, you have to have your master at -72db to mix at 12bit, I frankly doubt anyone mix at those levels.

    Report
  • finally someone’s addressed the reality of the situation. some much needed pragmatic advice

    Report
  • Nice article that addresses many things that I have stumbled on. Such as when I adjusted my seat to my keyboards high enough caused me legs to hurt above and behind the knees because my feet didn’t touch the floor well enough. The solution was to lower the keyboard stand.

    Few hints and my learning experience:

    The modern computer master volume is outside the bit domain of the soundcard. and won’t cause degradion Use that if you have nothing else. Even the most basic built in audio chipset is at least 24 bit nowadays anyway.

    The german Beat magazine has several free plugins that are excellent.
    drumMic’a is a good free drum plugin.

    I spent around 9 days in selecting a DAW few years ago. A one called Energy XT was by far the easiest to learn in my opinion. but deceptively powerful. The drawback is that the looks are dated and until recently not in much development.
    I own now couple of other DAWS, but it is still my favorite.

    Cakewalk has often excellent sales on their synths and their entry level DAWs at great discounts.
    Isotope Nectar Elements is often on sale and powerful and easy to use plugin for voice.

    Today I mainly use 3 commercial synths. The reason is that I invested time in studying them (as this artivce recommends and found that I could do virtually anything that I need). One is sample based, one a hybrid and the third is analog.

    I found out I was spending to much time in checking out free synths. Don’t do the same, select rather few and stick to them.

    I use mostly free effects or the ones that come with my DAW’s, (apart from Nectar Elements). I find it sufficient and think it will suffice most people (non pros).

    I found creating a whole song a bit overwhelming. By sticking to smaller pieces but doing them well increased my confidence.

    My other weak point was lack of experience with drums. Using and studying midi drum clips and modifying them rather then creating new beats, helped a lot in the beginning.
    Also realizing that I spent too much time in tweaking sound of the beat in the beginning as I had wrong ideas of how it would sound in the final mix.

    Report
  • Yup – even though on a 24bit system, using only 12-bits is theoretically down at -72db and Javier Z mentions that people don’t mix at that level, you’d be surprised at the way some people set their gain structure in a DAW – especially when using buses/groups, and then use the DAW’s output level as an overall monitoring volume control.
    So 12-bits isn’t necessarily common, but i’ve seen it.

    Report
  • Speaker placement:
    ” NOT TOO NEAR THE REAR WALL, ”

    Well, Genelec recommends to keep the speakers either on the back wall or over 1 meter from the backwall. Backwall being as good as one meter. For most homestudios it’s better to have speakers on the backwall for most controll over the sound.

    Report

Leave a Reply

Your email address will not be published. Required fields are marked *

You currently have an ad blocker installed

Attack Magazine is funded by advertising revenue. To help support our original content, please consider whitelisting Attack in your ad blocker software.

Find out how

x

    A WEEKLY SELECTION OF OUR BEST ARTICLES DELIVERED TO YOUR INBOX